Yamaha PM5D V2 Digital Mixer driver for Windows 7 - Yamaha PM5D V2 Digital Mixer driver from Yamaha f

Yamaha PM5D V2 Digital Mixer 2.27

Yamaha PM5D V2 Digital Mixer driver from Yamaha for OS Independent

Yamaha PM5D V2 Digital Mixer driver from Yamaha for OS Independent

Publisher review for Yamaha PM5D V2 Digital Mixer 2.27:

Before install Yamaha PM5D V2 Digital Mixer 2.27you should set a system restore point, to make sure you can rollback to your original driver in case you accidentally install another driver or select the driver for another version of the operating system.

Also, do not forget to check with our site as often as possible for new version of Yamaha PM5D V2 Digital Mixer . We recommend to always use most recent version of a driver.

This package provides the necessary installation files of Yamaha PM5D V2 Digital Mixer Firmware 2.27.Improvements:- A minor change in manufacturing and improved quality control process for PM5D and DSP5D requires the new Firmware V2.27 (DSP5D V1.27). 
Important notice:Make sure to unplug the cable connected to the rear-panel HA REMOTE connector during the update operations. Especially on the PM5D-RH, this may cause the internal head amps to be uncontrollable. If this happens, follow the procedures described in the upgrade guide..
Installation steps:
1. Turn the PM5D on. The opening screen appears as usual and the UPLOAD MENU screen appears. On the left side the current firmware version of each PM5D CPU is shown and on the right side the corresponding firmware version transmitted from the memory card is shown. If the left and right firmware versions differ from each other, the corresponding UPLOADER SELECT button automatically turns on. Please note that when you try to update the PM5D-RH MAIN or LCD, the UPLOADER SELECT buttons for AD IN/STIN are not turned on since the AD IN/STIN versions are not shown. To update AD IN/STIN, first update MAIN and LCD.
2. Click the UPLOAD in the bottom center of the screen to start updating the corresponding CPU. The progress bar will appear indicating the progress of the update.
3. When the progress bar shows “100%” and the “Please Re-start!” message appears, turn the PM5D off and on again. The update of each CPU is complete if you do not need to update AD IN/STIN of the PM5D-RH.
4. After turning on the power to the PM5D-RH, follow step 2 and 3 in the UPLOAD MENU screen to update another CPU for which the UPLOADER SELECT buttons are on.
NOTE:- If you are using the PM5D-RH and the AD IN/STIN versions are not shown, try erasing the PM5D firmware and updating AD IN/STIN again by following the steps below.
1. While holding down the [RECALL] button and the [SHIFT] button, turn the power to the PM5D-RH to display the UPLOAD MENU screen.
2. Select all AD IN/STIN firmware by clicking the SEL buttons at the left of “AD IN/STIN” in “CURRENT FIRMWARE,” then click the ERASE button.
3. Click the OK button to execute the operation. All AD IN/STIN firmware will be erased.
4. When all the firmware is erased, turn off the PM5D-RH, then while holding down the [RECALL] button and the [SHIFT] button, turn the power to the PM5D-RH again to call up the UPLOAD MENU screen. If the AD IN/STIN firmware is erased, all the +48V LEDs in the AD IN section on the top panel flash.
5. On the UPLOAD MENU screen, turn on all the AD IN/STIN UPLOADER SELECT buttons, then click the UPLOAD button. The selected AD IN/STIN will be updated and the progress bar will appear indicating the progress of the update. During the operation, the AD IN/STIN fields in CURRENT FIRMWARE/UPLOADER still remain blank (this is normal). Never attempt to turn off the power until the update is complete.
6. When the progress bar shows “100%” and a message “Please Re-start!” appears, turn the PM5D-RH off and on again.
7. Confirm that all the AD IN/STIN versions are shown in the PREFERENCE 2 screen for the UTILITY function.

Operating system:
OS Independent